Introducing the new PV monitoring package designed to work with an SMA cluster controller. The package includes a silicon-cell pyranometer with a mounting bracket, Class A PRT back-of-panel temperature sensor with Kapton tape, fan-aspirated solar radiation shield with 24 V-12 V DC converter, and Class A PRT air temperature sensor with TS-100 port adapter.
Fan-Aspirated Solar Radiation Shield (TS-100)
- Prevents solar radiation induced errors
- Long life, IP55 rated fan
- Meets IEC 61724-1 requirements
More information on the TS-100 available here.
- Includes 24 V-12 V DC Converter
We are currently looking for case studies for this product. If you would like to share your application of this product, please click here.
Current Stock:
SP-214 Silicon-cell Pyranometer
Specifications
Power Supply
5 to 36 V DC with a maximum current drain 22 mA (2 mA quiescent current drain)
Sensitivity
0.013 mA per W mˉ²
Calibration Factor
78 W mˉ² mA (reciprocal of sensitivity) with an offset of 4.0 mA
Calibration Uncertainty
± 5 %
Calibrated Output Range
4 to 20 mA
Measurement Repeatablitiy
Less than 1 %
Non-stability (Long-term Drift)
Less than 2 % per year
Non-linearity
Less than 1 % (up to 1250 W mˉ², maximum radiation measurement is 1250 w mˉ²)
Response Time
Less than 1 ms
Field of View
180 ˚
Spectral Range
360 to 1120 nm (wavelengths where response is 10 % of maximum)
Directional (Cosine) Response
±5 % at 75 ˚ zenith angle
Temperature Response
0.04 ± 0.04 % per C
Operating Environment
-40 to 70 C, 0 to 100 % relative humdiity, can be submerged in water up to depths of 30 m
Dimensions
24 mm diameter, 28 mm height
Cable
5 m of shielded, twisted-pair wire with santoprene rubber jacket (high water resistance, high UV stability, flexibility in cold conditions)
Mass
140 g ( with 5 m of lead wire)
Warranty
4 years against defects in materials and workmanship
CS240 Back-of-Pannel Temperature Sensor
Specifications
Element Type
Precision 1000 Ω class A platinum sensing element
Tolerance
± (0.15 + 0.002t)
Temperature Coefficient
TCR = 3850 ppm/K
Long-Term Stability
Maximum R₀ drift 0.04 % (after 1000 h at 400 C)
Measuring Current
0.1 to 0.3 mA
Operating Tempertature Range
-40 to 105 C
Disk Material
Anodized aluminum
Cable Jacket Material
Black semi-gloss PVC, UL VWˉ¹ sunlight-resistant for outdoor use
Disk Diameter
25.4 mm
Overall Probe Length
63.5 mm
Overmolded Joint Dimensions
57.2 x 11.2 x 14.7 mm
ST-150 Class A PRT
Specifications
Measurement Range
-50 to 70 C
Measurement Uncertainty
0.3 C (-40 to 60 C), Class A
Measurement Repeatability
Less than 0.01 C
Long-term Drift
Less than 0.05 C per year
Equilibration Time
15 seconds
Self-heating
Less than 0.01 C (typical, assuming pulsed excitation of 2.1 V DC), 0.09 at 5 C (max. assuming continuous input excitation of 2.1 V DC)
Operating Environmental
-50 to 70 C, 0 to 100 % relative humidity
Input Voltage Requirement
Datalogger dependent
Output Voltage Requirement
Datalogger dependent
Current Draw
Datalogger dependent
Dimensions
56 mm, 3 mm diameter
Mass
95 g
Warranty
4 years against defects in materials and workmanship
TS-100 Fan-Aspirated Radiation Shield
Specifications
Difference among Individual Replicate Shields
Less than 0.1 C
Aspiration Rate
6 m sˉ¹ at full-speed, 3 m sˉ¹ at half-speed
Fan Input Voltage Requirement
10.8 to 13.2 V DC
Fan Current Drain
80 mA at full-speed, 25 mA at half-speed
Fan Dust and Water Protection
IP55
Dimensions
220 mm height, 270 mm diameter
Mass
840 g
Cables
5 m of shielded, twisted-pair wire for fan and air temperature sensors with santoprene rubber jacket (high water resistance, high UV stability, flexibility in cold conditions), pigtail lead wires
Warranty
4 years against defects in materials and workmanship